小米電視root需要做哪些準備工作？2024小米電視刷機詳細教程

萌萌的小確幸 · 發表于 2024-7-8 13:11

最近有不少人問我家里的小米電視root需要做哪些準備工作？哪些是作為一個新手最需要準備的，今天就給大家做一個2024小米電視刷機詳細教程。

一、小米電視root需要做哪些準備工作？2024小米電視刷機詳細教程

注意：這不是 root 電視的完整教程,，但是包含了進入電視系統底層的各種準備工作. 能夠進入電視系統底層之后, 任何有 magisk 使用經驗的人都可以輕松實現 root.

測試設備: 小米電視 A43 pro (L43MA-AP) (2023 年上市)

警告 (免責聲明)： 操作有風險, 包括但不限于數據丟失, 設備損壞, 失去保修等，所以大家需要謹慎刷機。

1.來源

本文使用的各種方法并非原創, 而是主要來自于以下幾篇文章：

(ZNDS 智能電視網) 教程&攻略 2022新款小米電視（安卓6以上）硬核root教程（需要USB轉TTL）

http://kinema24.com/tv-1228229-1-1.html

(ZNDS 智能電視網) 教程&攻略小米電視硬核root教程（需要USB轉TTL硬件工具）

http://kinema24.com/tv-1203308-1-1.html

2.啟用adb并安裝apk

本章所需硬件設備: 小米電視, 小米電視的遙控器, PC (臺式機或筆記本), 本地局域網絡 (有線以太網或無線 WIFI)。

2.1 正常開機, 先看一下系統信息

進入電視設置

關于: MIUI TV 版本: MiTV OS 2.8.2129 (穩定版)

設備信息: 屏幕參數 3840x2160 43英寸, 存儲內存 2GB 閃存 32GB, 無線連接 2.4GHz/5GHz 藍牙, 操作系統 Android.

存儲空間: 共 30536MB, 系統 4446MB.

2.2 在設置中的【關于】頁面找到產品型號 (MiTV):

選中產品型號然后連續多次點擊遙控器上的確認按鍵, 即可進入開發者模式.

2.3 在設置中的帳號與安全頁面, 將 ADB調試選項打開：

ADB 調試這個開關只有在上一步開啟開發者模式后才會出現. 并且每次重啟之后, 這個選項都會自動關閉

2.4 通過有線以太網或無線 wifi 將設備聯網, 然后看一下設備的 IP 地址 (下圖已打馬)：

比如此處設備的 IP 地址是 192.168.33.121

注意, 只需要將設備連接至本地局域網, 能夠通過 DHCP 獲取 IP 地址即可, 無需連接互聯網 (Internet).

2.5 在 PC (臺式機或筆記本) 上安裝 adb工具, 然后執行命令：

> adb connect 192.168.33.121
connected to 192.168.33.121:5555
> adb devices
List of devices attached
192.168.33.121:5555 device

復制代碼

需要在電視上使用遙控器同意 adb 調試.

此時就成功通過 adb 連接到了電視！

2.6 在 PC 上使用 adb 安裝 apk, 比如

adb install aida64-v198.apk

復制代碼

重復使用這個命令, 就可以安裝多個應用

如果安裝命令執行成功后, 沒有顯示出應用圖標, 可以重啟電視

3.開機進入recovery

本章所需硬件設備: 小米電視, 小米電視的遙控器

3.1 關機, 拔掉電源.

注意, 一定要拔掉電源, 僅僅關機是不夠的.

3.2 (適用于藍牙遙控器)

同時按住遙控器上的確認和返回按鍵, 如圖 (黃圈標記):

按住遙控器按鍵不松手, 插電開機。進入recovery界面如圖：

4.制作HDMI轉 UART (TTL 5V) 調試線

本章所需硬件設備: HDMI 插頭 (或 HDMI 線), USB 轉 UART 模塊 (推薦 CP2102), 杜邦線, 萬用表 (可選), 剪刀、螺絲刀等小工具.

在淘寶等購買 HDMI 插頭 (推薦 HDMI 免焊接插頭, 方便接線), 以及 USB 轉 UART 模塊 (推薦 CP2102 型號), 照片如圖:

按照下表接線：

HDMI 引腳	CP2102 模塊	備注
14	+5V	電源
15	TXD	UART 發送
16	RXD	UART 接收
20	GND	接地

注意: 5V電源線必須連接, 如果不接則 UART 不會有輸出.

接線后照片：

小米電視root需要做哪些準備工作？2024小米電視刷機詳細教程

如果有萬用表, 可以在接線之后測量一下是否連通。

5.開機進入uboot

本章所需硬件設備: 小米電視, 章節 (3) 制作的調試線, PC (臺式機或筆記本)

注意: 這臺設備的 UART 波特率為 921600 ! (之前使用 115200 一直是亂碼)

5.1 將調試線的 USB 轉 UART 模塊插到 PC, 并打開 UART.

使用哪種操作系統, 以及串口軟件都可以. 以下栗子只是多種可能之一

操作命令舉例 (操作系統 ArchLinux)

插上 CP2102 模塊:

> lsusb
Bus 001 Device 006: ID 10c4:ea60 Silicon Labs CP210x UART Bridge
> ls -l /dev/tty*
crw-rw---- 1 root uucp 188, 0 12月26日 15:40 /dev/ttyUSB0

復制代碼

此處 CP2102 USB 轉 UART 模塊出現為設備文件 /dev/ttyUSB0

設置波特率為921600:

> stty -F /dev/ttyUSB0 ispeed 921600 ospeed 921600
> stty -F /dev/ttyUSB0 speed
921600

復制代碼

打開 UART：

> cu -l /dev/ttyUSB0
Connected.

復制代碼

如果沒有 cu 命令, 可以安裝 uucp:

> sudo pacman -S uucp

復制代碼

5.2 將調試線的 HDMI 插頭插到電視的 HDMI 1 插座, 如圖:

正常開機狀態下, 重啟電視. 然后應該能看到 UART 輸出的啟動日志

AOCPU unknown cmd=20
[VRTC] xMboxSetRTC val=0x64373481
T5:BL:b49668;ID:4D32583237340F0000250D01;FEAT:B0F875B4:280000;POC:F;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
aml log : uart_clk_enhance() need fine tune
efuse adjust vddee vol,get efuse index value:0002
use efuse adjust vddee voltage, set vol 0.84v
bl2_stage_init 0x01
L0:00001803
L1:00000702
L2:00008060
L3:00000000
SIP:0006c6a
TE: 117954
BL2 Aarch32 Built : 15:50:08, Mar 17 2023. t5 g2df8b51 - zhiguang.zhang@droid08-bj
aml log : T5 efuse_get_sar_adc_ref() need fine tune
Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1800 MHz
Set clk81 to 166.6M
aml log : bl2_platform_setup() need fine tune
eMMC boot [url=home.php?mod=space&uid=103582]@[/url] 0
sw-hs 00000000
s
sw8 s
storage init finish
DDR debug 1 p_acs_set=fffc30f0,come here plat/t5/ddr/ddr.c ,207
aml log : not USB BOOT...
DDR_DRIVER_VERSION: AML_A_PHY_V_1_2; Built : 15:50:08, Mar 17 2023. t5 g2df8b51 - zhiguang.zhang@droid08-bj
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffc4fbc, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 0
enable_fast_boot
dram_type==DDR4
config==Rank01_32bit_ch0
DDR : DDR4 Rank01_32bit_ch0
Set ddr clk to 1176 MHz
DDR debug 1 dram_vref_reg_value=00000016 plat/t5/ddr/ddr_lib.c ,4844
CS0 size: 1024MB
CS1 size: 1024MB
Total size: 2048MB @ 1176MHz
DDR : 2048MB @1176MHz
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
bdlr_step_size ps=397
rpmb not init until <register.h> have been fixed
Load FIP HDR from eMMC, src: 0x00014200, des: 0x00200000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00018200, des: 0x00204000, size: 0x00138000, part: 0
boot BL31
NOTICE: BL31: v1.3(release):e2d6c4e91
NOTICE: BL31: Built : 15:39:27, May 20 2021
BL31:tsensor calibration rev, buf1[1], buf1[0]: 0x2, 0x80, 0xc
BL31:tsensor calibration: 0x8600000c
tsensor reg: 0x20d4
mhu init done-v2
NOTICE: BL31: T5 secure boot!
NOTICE: BL31: BL33 decompress pass
Starting IANFO: BL3-2: ATOS-V2.4.4-145-gf6c6ed9e2 #1 Wed Dec 16 12:45:54 2020 +0800 arm
INFO: BL3-2: Chip: T5 Rev: B (34:B - 10:11)
INFO: BL3-2: crypto engine DMA
INFO: BL3-2: secure time TEE
INFO: BL3-2: CONFIG_DEVICE_SECURE 0xb200000e
OCPU FreeRTOS
AOCPU image version='(no 6774b479c2e09162650601c4c33d8a1f194dd5f1 15:55:52 2023-04-04'
[AOCPU]: mailbox init start
reg idx=0 cmd=6 handler=100051da
reg idx=1 cmd=7 handler=100051c4
[AOCPU]: mailbox -v1 init end
reg idx=2 cmd=9 handler=100057ca
Starting timer ...
reg idx=3 cmd=b4 handler=10002a4e
reg idx=4 cmd=b6 handler=10002992
reg idx=5 cmd=11 handler=100017b0
reg idx=6 cmd=12 handler=100017e8
reg idx=7 cmd=4 handler=100019b6
reg idx=8 cmd=30 handler=100019a2
reg idx=9 cmd=31 handler=100019b2
Starting task scheduler ...
protect cbus registers
U-Boot 2015.01-g9fb9269-mulan_a-22 (Apr 04 2023 - 15:55:49), Build: jenkins-uboot_Mulan_A-22
DRAM: 2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spicc): req_seq = 0
register usb cfg[0][1] = 0000000077f4dae8
gpio: pin GPIOD_2 (gpio 2) value is 0
gpio: pin GPIOD_3 (gpio 3) value is 1
gpio: pin GPIOB_12 (gpio 48) value is 0
gpio: pin GPIOB_13 (gpio 49) value is 0
MMC: aml_priv->desc_buf = 0x0000000073e35cd0
aml_priv->desc_buf = 0x0000000073e38010
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
aml log : R2048 check pass!
Amlogic Multi-DTB tool
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
ddr size = 80000000
Found DTB for "t5_mulan_01_2g"
start dts,buffer=0000000073e3a860,dt_addr=0000000073e3b060
get_partition_from_dts() 80: ret 0
parts: 19
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 11
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11:secure_recovery 0000000002000000 1
12:factorydata 0000000000a00000 11
13: vendor 0000000020000000 1
14: odm 0000000008000000 1
15: system 0000000060000000 1
16: product 0000000002000000 1
17: cache 0000000020000000 2
18: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x27400000
aml log : internal sys error!
reboot_mode=normal
gpio: pin GPIOD_7 (gpio 7) value is 1
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 21656022, store 21656022
_verify_dtb_checksum()-3476: calc 21656022, store 21656022
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
aml log : R2048 check pass!
Amlogic Multi-DTB tool
Multi DTB detected.
Multi DTB tool version: v2.
Support 2 DTBS.
ddr size = 80000000
Found DTB for "t5_mulan_01_2g"
amlkey_init() enter!
calc 62758a9f50c, store 62758a9f50c
calc 62758a9f50c, store 62758a9f50c
do nothing
[EFUSE_MSG]keynum is 4
co-phase 0x3, tx-dly 0, clock 40000000
co-phase 0x3, tx-dly 0, clock 40000000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
switch to partitions #0, OK
mmc1(part 0) is current device
current model_name: dzvc_01_20
mmc env offset: 0x27400000
Writing to MMC(1)... done
D/ model: handle_lcd_phy, phy_lane_ctrl[0] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[1] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[2] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[3] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[4] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[5] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[6] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[7] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[8] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[9] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[10] is (0x37)
D/ model: handle_lcd_phy, phy_lane_ctrl[11] is (0x37)
[KM]Error:f[keymanage_dts_get_key_device]L99:lcd_optical key name is not exist
[KM]Error:f[_get_km_ops_by_name]L247:key lcd_optical not know device 5
[KM]Error:f[key_unify_query_exist]L367:key[lcd_optical] not cfg in dts
E/ UnifyKey: checkUnifyKey, lcd_optical query exist error.
E/ ini_io: check_hex_data_have_header_valid, rd data len error (0x0, 0xffffffff)
D/ model: handle_panel_ini, check lcd_optical param data diff (0xffffffff), save new param.
[KM]Error:f[keymanage_dts_get_key_device]L99:lcd_optical key name is not exist
[KM]Error:f[_get_km_ops_by_name]L247:key lcd_optical not know device 5
[KM]Error:f[key_unify_write]L278:key[lcd_optical] no cfg in dts
vpu: clk_level in dts: 7
vpu: vpu_power_on_new
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd1 matrix rgb2yuv..............
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
hdr_func 1, hdr_process_select 0x1
lcd: lcd_debug_print flag: 0
lcd: detect mode: tv, key_valid: 1
lcd: load lcd_config from unifykey
lcd_phy_probe
lcd: unifykey version: 0x0002
lcd: unifykey version: 0x0002
lcd: tcon: rsv_mem addr:0x2bc00000, size:0xc00000
lcd: lcd_tcon_bin_path_update: init_load: 0
lcd: tcon: load init data len: 6356, ver: 20221009
lcd: lcd_tcon_bin_load
E/ model: handle_tcon_data_load, tcon_data[4] file name "/param/tcon_demura.bin" not exist.
lcd extern: load config from unifykey
lcd extern: add driver ext_default(0)
lcd: lcd_extern_config_update_dynamic_size size:0x2b
lcd: lcd_extern_config_update_dynamic_size size:0x0
lcd: lcd_extern_config_update_dynamic_size size:0x0
lcd extern: aml_lcd_extern_probe: index(0->0) ok
lcd: load backlight_config from unifykey
lcd: bl: unifykey version: 0x0001
lcd: bl: pinctrl_version: 2
lcd: bl: name: bl_pwm, method: 2
lcd: bl: bl_level: 127
lcd: bl: aml_bl_power_ctrl: 0
aml log : internal sys error!
s_version: U-Boot 2015.01-g9fb9269-mulan_a-22
do_factorydata_read:258 Can't find out dcdc from factorydata.
factorydata - Access the factorydata from Xiaomi Partition
Usage:
factorydata argv:
dump
read keyname
write keyname value
erase keyname
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
soc_family_id==0x00000034
table_max=0000000c,p_ddr_base_add=77f4b9c0,chip_id=00000034
table_index=00000000,p_ddr_base_add=77f4b9c0,(p_ddr_base->chip_id==00000028
no find match chip id=0x00000034, ,G12A will use default value
table_index=00000001,p_ddr_base_add=77f4ba10,(p_ddr_base->chip_id==00000029
no find match chip id=0x00000034, ,G12B will use default value
table_index=00000002,p_ddr_base_add=77f4ba60,(p_ddr_base->chip_id==0000002e
no find match chip id=0x00000034, ,TL1 will use default value
table_index=00000003,p_ddr_base_add=77f4bab0,(p_ddr_base->chip_id==0000002b
no find match chip id=0x00000034, ,SM1 will use default value
table_index=00000004,p_ddr_base_add=77f4bb00,(p_ddr_base->chip_id==0000002f
no find match chip id=0x00000034, ,TM2 will use default value
table_index=00000005,p_ddr_base_add=77f4bb50,(p_ddr_base->chip_id==0000002c
no find match chip id=0x00000034, ,A1 will use default value
table_index=00000006,p_ddr_base_add=77f4bba0,(p_ddr_base->chip_id==00000030
no find match chip id=0x00000034, ,C1 will use default value
table_index=00000007,p_ddr_base_add=77f4bbf0,(p_ddr_base->chip_id==00000033
no find match chip id=0x00000034, ,C2 will use default value
table_index=00000008,p_ddr_base_add=77f4bc40,(p_ddr_base->chip_id==00000032
no find match chip id=0x00000034, ,SC2 will use default value
table_index=00000009,p_ddr_base_add=77f4bc90,(p_ddr_base->chip_id==00000034
find match chip id=0x00000034 ,T5
uboot auto fast boot check flash data is ok return
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
pll tsensor avg: 0x20da, u_efuse: 0xc
temp1: 45
device cool done
[OSD]load fb addr from dts:/meson-fb
[OSD]load fb addr from dts:/fb
[OSD]set initrd_high: 0x2b400000
[OSD]fb_addr for logo: 0x2b400000
[OSD]load fb addr from dts:/meson-fb
[OSD]load fb addr from dts:/fb
[OSD]fb_addr for logo: 0x2b400000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x2b400000 width=3840, height=2160
[OSD]osd_hw.free_dst_data: 0,3839,0,2159
[OSD]osd1_update_disp_freescale_enable
vpp: vpp_matrix_update: 0
vpp: g12a/b post2(bit12) matrix: YUV limit -> RGB ..............
lcd: enable: ST4251D02_1, p2p, 3840x2160@60. 0Hz
lcd: tv driver init(ver 20221101): p2p
lcd: reset tcon
lcd: lcd_pll_wait_lock: pll_lock=1, wait_loop=1
lcd: set pll spread spectrum: 15, 30000ppm
lcd: set pll spread spectrum: freq=0, mode=0
vpp: vpp_init_lcd_gamma_table
[info]spicc_probe: amlogic,meson-g12a-spicc @00000000ffd13000
[info]spicc_cs_gpio_init: cs_gpio[0]=22
[info]spicc_cs_gpio_init: total (1) slaves
SF: Detected XM25QH80B with page size 256 Bytes, erase size 4 KiB, total 1 MiB
spi read test ok spi_read_test
lcd: error: spi read test ok
lcd: lcd_tcon_core_reg_set
lcd: error: lcd_tcon_data_set: data index -1 is invalid
lcd extern: lcd_extern_power_ctrl: ext_default(0): 1
lcd: bl: set level: 127, last level: 0
lcd: bl: aml_bl_power_ctrl: 1
lcd: clear mute
Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
[imgread]szTimeStamp[2023041122493711]
[imgread]secureKernelImgSz=0x866000
aml log : R~2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 buildvariant=user
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
Amlogic Multi-DTB tool
Single DTB detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
Loading Kernel Image(COMP_NONE) ... OK
kernel loaded at 0x01080000, end = 0x018b9000
libfdt fdt_getprop(): FDT_ERR_NOTFOUND
Loading Device Tree to 0000000009fe7000, end 0000000009fff559 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 3036492 us
vmin:72 b2 6 0!
[VRTC]: xMboxGetRTC val=0x64373481
[cec_get_portinfo]: info=0x0
AOCPU unknown cmd=b5

復制代碼

如果看到類似上面的輸出, 說明調試線及各種設置一切正常！

5.3 再次重啟, 同時快速連續多次按回車鍵, 直到進入 uboot 命令行

s_version: U-Boot 2015.01-g9fb9269-mulan_a-22
do_factorydata_read:258 Can't find out dcdc from factorydata.
factorydata - Access the factorydata from Xiaomi Partition
Usage:
factorydata argv:
dump
read keyname
write keyname value
erase keyname
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
mulan#
mulan#
mulan#
mulan#

復制代碼

好了, 這就進入 uboot 命令行了 ! 我們先來查看一些信息

執行 printenv 命令:

mulan#printenv
DisableSelinux=permissive
EnableSelinux=enforcing
Irq_check_en=0
Ramoops_io_dump=0
Ramoops_io_en=0
Ramoops_io_skip=1
assm_mn=DZVCARF3B18TXNXX02321
assm_sn=48276106100061401
baudrate=115200
bl_level=127
boot_part=boot
bootargs=init=/init ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=osd0,loaded,0x3d800000 powermode=on fb_width=1920 fb_height=1080 display_bpp=16 outputmode=2160p60hz vout=2160p60hz,enable panel_type= lcd_ctrl=0x00001185 osd_reverse=n video_reverse=0 androidboot.firstboot=0 jtag=disable irq_check_en=0 ramoops_io_en=0 ramoops_io_dump=0 ramoops_io_skip=1 androidboot.mi.panel_size=43 bl_level=127 androidboot.mi.panel_vendor=csot androidboot.mi.panel_resolution=3840x2160 androidboot.panel_type=20 androidboot.reboot_mode=normal androidboot.platform_id=1180 androidboot.model_name=dzvc_01_20 androidboot.redmi=false androidboot.hwid=01 androidboot.serialno=48276106100061401 androidboot.mac=78:53:33:10:dd:a5 androidboot.assm_mn=DZVCARF3B18TXNXX02321 androidboot.did_key=00CB00073C3B|754663978|k5sBrXtwBJ6BLv5O loglevel=0 androidboot.console_enable=0 androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01-g9fb9269-mulan_a-22 androidboot.build.expect.baseband=N/A androidboot.provider=amlogic androidboot.watchdog=enabled androidboot.mi.panel_buildin=true androidboot.mi.panel_3d_attribut=0 androidboot.mi.cpu=Cortex-A35 androidboot.mi.gpu=Mali-G31
bootcmd=ddr_auto_fast_boot_check 6; run switch_bootmode
bootdelay=1
bootloader_version=U-Boot 2015.01-g9fb9269-mulan_a-22
cec_ac_wakeup=1
cec_fun=0x2F
cmdline_keys=if factorydata read assm_sn; then setenv bootargs ${bootargs} androidboot.serialno=${assm_sn};else setenv bootargs ${bootargs} androidboot.serialno=1234567890;fi;if factorydata read mac; then setenv bootargs ${bootargs} androidboot.mac=${mac};fi;if factorydata read assm_mn; then setenv bootargs ${bootargs} androidboot.assm_mn=${assm_mn};fi;if factorydata read did_key; then setenv bootargs ${bootargs} androidboot.did_key=${did_key};fi;if factorydata read dcdc; then setenv bootargs ${bootargs} androidboot.dcdc=${dcdc};fi;if factorydata read log_level; then setenv bootargs ${bootargs} loglevel=${log_level};else setenv bootargs ${bootargs} quiet;fi;if factorydata read console_enable; then setenv bootargs ${bootargs} androidboot.console_enable=${console_enable};if itest ${console_enable} != 0; then setenv bootargs ${bootargs} ${console_userdebug};fi;else setenv bootargs ${bootargs} ${console_userdebug};fi;if factorydata read mitv_screen_on; then if test ${mitv_screen_on} = false; then factorydata write mitv_screen_on 'true';else factorydata write mitv_screen_on 'true';setenv mitv_screen_on true;fi;else factorydata write mitv_screen_on 'true';setenv mitv_screen_on true;fi;
console_enable=0
console_userdebug=console=ttyS0,921600 no_console_suspend earlycon=aml-uart,0xffd23000 printk.devkmsg=on
did_key=00CB00073C3B|754663978|k5sBrXtwBJ6BLv5O
display_bpp=16
display_color_bg=0
display_color_fg=0xffff
display_color_index=16
display_height=1080
display_layer=osd0
display_width=1920
dtb_mem_addr=0x1000000
edid_14_dir=/odm/etc/tvconfig/hdmi/port_14.bin
edid_20_dir=/odm/etc/tvconfig/hdmi/port_20.bin
edid_select=0
factory_reset_poweroff_protect=if test ${wipe_data} = failed; then echo wipe_data=${wipe_data};run update;fi;if test ${wipe_cache} = failed; then echo wipe_cache=${wipe_cache};run update;fi;
fb_addr=0x3d800000
fb_height=1080
fb_width=1920
fdt_high=0x20000000
ffv_freeze=off
ffv_wake=off
firstboot=0
frac_rate_policy=1
fs_type=root=/dev/mmcblk0p20 ro rootwait skip_initramfs
hdmimode=2160p60hz
hdr_policy=1
hwid=01
init_display=osd open;osd clear;if test ${redmi} = true; then imgread pic logo redmi ${loadaddr};bmp display ${redmi_offset};else imgread pic logo bootup ${loadaddr};bmp display ${bootup_offset};fi;bmp scale;vout output ${outputmode}
initargs=init=/init ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000
irremote_update=if irkey 2500000 0xe31cfb04 0xb748fb04; then echo read irkey ok!; if itest ${irkey_value} == 0xe31cfb04; then run update;fi;fi;
jtag=disable
lcd_ctrl=0x00001185
lcd_init_level=0
led_brightness=0xff
loadaddr=1080000
lock=10101000
log_level=0
logic_addr=0x0
mac=78:53:33:10:dd:a5
mitv_screen_on=true
model_edid=/odm/etc/tvconfig/hdmi/port_14.bin
model_name=dzvc_01_20
model_panel=/odm/panel/CSOT_ST4251D02-1/p2p_cspi_cvte.ini
model_tcon=/odm/panel/CSOT_ST4251D02-1/p2p_cspi.bin
model_tcon_bin_header=1
model_tcon_ext_b0=null
model_tcon_ext_b0_spi=/param/tcon_p_gamma.bin
model_tcon_ext_b1=null
model_tcon_ext_b1_spi=null
model_tcon_ext_b2=null
model_tcon_ext_b2_spi=null
model_tcon_ext_b3=null
model_tcon_ext_b3_spi=null
osd_reverse=n
otg_device=0
outputmode=2160p60hz
panel_name=ST4251D02_1
panel_resolution=3840x2160
panel_reverse=0
panel_size=43
panel_vendor=csot
platform_id=1180
port_map=4312
powermode=on
preboot=run storeargs;
ramdump_enable=1
reboot_mode=normal
recovery_from_flash=if itest ${upgrade_step} == 3; then if ext4load mmc 1:2 ${dtb_mem_addr} /recovery/dtb.img; then echo cache dtb.img loaded; fi;if ext4load mmc 1:2 ${loadaddr} /recovery/recovery.img; then echo cache recovery.img loaded; bootm ${loadaddr}; fi;fi;if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then bootm ${loadaddr}; fi;
recovery_from_udisk=if fatload usb 0 ${loadaddr} mulan.autoscript; then autoscr ${loadaddr}; fi;if fatload usb 0 ${loadaddr} mulan.recovery; then if fatload usb 0 ${dtb_mem_addr} mulan.dtb; then echo udisk dtb loaded; fi;bootm ${loadaddr};fi;
recovery_fs_type=root=ramfs
recovery_offset=0
recovery_part=recovery
redmi=false
sdr2hdr=0
secureboot=setenv bootargs ${bootargs} ${recovery_fs_type} otg_device=0;run init_display;get_valid_slot;if imgread kernel secure_recovery ${loadaddr} 0; then bootm ${loadaddr}; fi;reboot;
stderr=serial
stdin=serial
stdout=serial
storeargs=get_rebootmode;get_bootloaderversion;setenv bootargs ${initargs} logo=${display_layer},loaded,${fb_addr} powermode=${powermode} fb_width=${fb_width} fb_height=${fb_height} display_bpp=${display_bpp} outputmode=${outputmode} vout=${outputmode},enable panel_type=${panel_type} lcd_ctrl=${lcd_ctrl} osd_reverse=${osd_reverse} video_reverse=${video_reverse} androidboot.firstboot=${firstboot} jtag=${jtag} irq_check_en=${Irq_check_en} ramoops_io_en=${Ramoops_io_en} ramoops_io_dump=${Ramoops_io_dump} ramoops_io_skip=${Ramoops_io_skip};setenv bootargs ${bootargs} androidboot.mi.panel_size=${panel_size} bl_level=${bl_level} androidboot.mi.panel_vendor=${panel_vendor} androidboot.mi.panel_resolution=${panel_resolution} androidboot.panel_type=${tag};setenv bootargs ${bootargs} androidboot.reboot_mode=${reboot_mode} androidboot.platform_id=${platform_id} androidboot.model_name=${model_name} androidboot.redmi=${redmi} androidboot.hwid=${hwid};run cmdline_keys;setenv bootargs ${bootargs} androidboot.hardware=amlogic androidboot.bootloader=${bootloader_version} androidboot.build.expect.baseband=N/A;setenv bootargs ${bootargs} androidboot.provider=amlogic androidboot.watchdog=enabled androidboot.mi.panel_buildin=true androidboot.mi.panel_3d_attribut=0 androidboot.mi.cpu=Cortex-A35 androidboot.mi.gpu=Mali-G31;
suspend=shutdown
switch_bootmode=bcb uboot-command;run factory_reset_poweroff_protect;run upgrade_check;if test ${reboot_mode} = cold_boot; then if adcdetect; then echo GOT secure_recovery key from ADC;run secureboot;fi;if irdetect; then echo GOT recovery key from IR;run update;fi;if monitor_bt_cmdline; then echo GOT recovery key from BT;run update;fi;if factorydata read factory_power_mode; then echo Factory power mode: ${factory_power_mode};if test ${factory_power_mode} = secondary;then systemoff;fi;fi;else boot_cooling;if test ${reboot_mode} = fastboot; then fastboot;else if test ${reboot_mode} = update; then setenv bootargs ${bootargs} ${recovery_fs_type} aml_dt=${aml_dt} recovery_part=${recovery_part} recovery_offset=${recovery_offset} androidboot.selinux=${DisableSelinux} otg_device=0;run init_display;run recovery_from_flash;else if test ${reboot_mode} = watchdog_reboot; then if test ${mitv_screen_on} = false; then monitor_bt_cmdline;echo watchdog enter system off;systemoff;fi;else if test ${reboot_mode} = kernel_panic; then if test ${mitv_screen_on} = false; then monitor_bt_cmdline;echo kernel_panic enter system off;systemoff;fi;else if test ${reboot_mode} = factory_reset; then setenv bootargs ${bootargs} ${recovery_fs_type} aml_dt=${aml_dt} recovery_part=${recovery_part} recovery_offset=${recovery_offset} androidboot.selinux=${DisableSelinux} otg_device=0;run init_display;run recovery_from_flash;fi; fi; fi; fi; fi; fi;run init_display;setenv bootargs ${bootargs} ${fs_type} androidboot.selinux=${EnableSelinux} otg_device=${otg_device} androidboot.led_brightness=${led_brightness};get_valid_slot;if imgread kernel boot ${loadaddr}; then bootm ${loadaddr}; fi;run storeargs;setenv bootargs ${bootargs} ${recovery_fs_type} aml_dt=${aml_dt} recovery_part=${recovery_part} recovery_offset=${recovery_offset} androidboot.selinux=${DisableSelinux} otg_device=0;run recovery_from_flash;
tag=20
update=setenv bootargs ${bootargs} ${recovery_fs_type} aml_dt=${aml_dt} recovery_part=${recovery_part} recovery_offset=${recovery_offset} androidboot.selinux=${DisableSelinux} otg_device=0;run init_display;if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;
upgrade_check=if itest ${upgrade_step} == 3; then echo upgrade_step=${upgrade_step}; run update;fi;
upgrade_step=0
video_reverse=0
wipe_cache=successful
wipe_data=successful
Environment size: 9759/65532 bytes
mulan#

復制代碼

uboot 命令行幫助信息

mulan#help
? - alias for 'help'
adcdetect- Detect ADC Key to start secure recovery system
adnl - use Amlogic DNL protocol
aml_bcb - aml_bcb
aml_sysrecovery- Burning with amlogic format package from partition sysrecovery
amlmmc - AMLMMC sub system
autoscr - run script from memory
avb - avb
base - print or set address offset
bcb - bcb
bmp - manipulate BMP image data
boot_cooling- cpu temp-system
booti - boot arm64 Linux Image image from memory
bootm - boot application image from memory
cec - Amlogic cec
clkmsr - Amlogic measure clock
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
dcache - enable or disable data cache
ddr_auto_fast_boot_check- ddr_fastboot_config cmd arg1 arg2 arg3...
ddr_auto_scan_drv- ddr_test_cmd cmd arg1 arg2 arg3...
ddr_auto_test_window- ddr_test_cmd cmd arg1 arg2 arg3...
ddr_cpu_test- ddr_test_cmd cmd arg1 arg2 arg3...
ddr_fast_boot- ddr_fastboot_config cmd arg1 arg2 arg3...
ddr_g12_offset_data- ddr_g12_offset_data 1 0 0 0 1 3
ddr_g12_override_data- ddr_g12_override_data 1 0 0 0 1 3
ddr_spec_test- DDR test function
ddr_test_cmd- ddr_test_cmd cmd arg1 arg2 arg3...
ddr_test_copy- ddr_test_copy function
ddrtest - DDR test function
defenv_reserv- reserve some specified envs after defaulting env
dspjtagreset- excute dsp jtag rest
dtimg - manipulate dtb/dtbo Android image
echo - echo args to console
efuse - efuse commands
efuse_user- efuse user space read write ops
emmc - EMMC sub system
env - environment handling commands
exit - exit script
ext4load- load binary file from a Ext4 filesystem
ext4ls - list files in a directory (default /)
ext4size- determine a file's size
factorydata- Access the factorydata from Xiaomi Partition
false - do nothing, unsuccessfully
fastboot- use USB Fastboot protocol
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fatsize - determine a file's size
fdt - flattened device tree utility commands
forceupdate- forceupdate
g12_d2pll- g12_d2pll 1300 1 0x10 0
get_avb_mode- get_avb_mode
get_bootloaderversion- print bootloader version
get_nearly_model- find the nearly model name
get_rebootmode- get reboot mode
get_system_as_root_mode- get_system_as_root_mode
get_valid_slot- get_valid_slot
go - start application at address 'addr'
gpio - query and control gpio pins
gpt - GUID Partition Table
guid - GUID - generate Globally Unique Identifier based on random UUID
hdmirx - hdmirx init function
help - print command description/usage
i2c - I2C sub-system
icache - enable or disable instruction cache
img_osd - image osd sub-system
imgread - Read the image from internal flash with actual size
ini - parse an ini file in memory and merge the specified section into the env
ini_model- parse ini file by env model_name
init_vpp- Initial VPP Module
irdetect- Detect IR Key to start recovery system
itest - return true/false on integer compare
jtagoff - disable jtag
jtagon - enable jtag
keyman - Unify key ops interfaces based dts cfg
keyunify- key unify sub-system
lcd - lcd sub-system
loadb - load binary file over serial line (kermit mode)
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
model_list- list ini model name
monitor_bt_cmdline- monitor_bt_cmdline
mw - memory write (fill)
mwm - mw mask function
nm - memory modify (constant address)
open_scp_log- print SCP messgage
osd - osd sub-system
panel_detect- Detect panel type from GPIO pin configuration
printenv- print environment variables
query - SoC query commands
rdext4pic- read logo bmp from ext4 part
readMetadata- readMetadata
read_temp- cpu temp-system
reboot - set reboot mode and reboot system
reset - Perform RESET of the CPU
ringmsr - Amlogic measure ring
rpmb_state- RPMB sub-system
rsvmem - reserve memory
run - run commands in an environment variable
saradc - saradc sub-system
saradc_12bit- saradc sub-system
saveenv - save environment variables to persistent storage
sdc_burn- Burning with amlogic format package in sdmmc
sdc_update- Burning a partition with image file in sdmmc card
set_active_slot- set_active_slot
set_trim_base- cpu temp-system
set_usb_boot- set usb boot mode
setenv - set environment variables
sf - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
spi_read_test- read spi
sspi - SPI utility command
startdsp- load dspboot.bin from address
store - STORE sub-system
systemoff- system off
tee_log_level- update tee log level
temp_triming- cpu temp-system
test - minimal test like /bin/sh
testcache- cache test
testsmp - test each CPU power on/off
true - do nothing, successfully
unpackimg- un pack logo image into pictures
usb - USB sub-system
usb_burn- Burning with amlogic format package in usb
usb_update- Burning a partition with image file in usb host
usbboot - boot from USB device
uuid - UUID - generate random Universally Unique Identifier
version - print monitor, compiler and linker version
viu_probe- enable viu probe in no secure chip
vout - VOUT sub-system
vout2 - VOUT2 sub-system
vpp - vpp sub-system
vpu - vpu sub-system
write_trim- cpu temp-system
write_version- cpu temp-system
mulan#

復制代碼

分區信息

mulan#mmcinfo
Device: SDIO Port C
Manufacturer ID: 9b
OEM: 100
Name: Y2P03
Tran Speed: 52000000
Rd Block Len: 512
MMC version 5.1
High Capacity: Yes
Capacity: (0x747c00000 Bytes) 29.1 GiB
mmc clock: 40000000
Bus Width: 8-bit
mulan#mmc part
Partition Map for MMC device 1 -- Partition Type: AML
Part Start Sect x Size Type name
00 0 8192 512 U-Boot bootloader
01 73728 131072 512 U-Boot reserved
02 221184 1048576 512 U-Boot cache
03 1286144 16384 512 U-Boot env
04 1318912 16384 512 U-Boot logo
05 1351680 49152 512 U-Boot recovery
06 1417216 16384 512 U-Boot misc
07 1449984 16384 512 U-Boot dtbo
08 1482752 16384 512 U-Boot cri_data
09 1515520 32768 512 U-Boot param
10 1564672 32768 512 U-Boot boot
11 1613824 32768 512 U-Boot rsv
12 1662976 32768 512 U-Boot metadata
13 1712128 4096 512 U-Boot vbmeta
14 1732608 65536 512 U-Boot tee
15 1814528 65536 512 U-Boot secure_recovery
16 1896448 20480 512 U-Boot factorydata
17 1933312 1048576 512 U-Boot vendor
18 2998272 262144 512 U-Boot odm
19 3276800 3145728 512 U-Boot system
20 6438912 65536 512 U-Boot product
21 6520832 54550528 512 U-Boot data
** Partition 22 not found on device 1 **
mulan#

復制代碼

重啟設備：

mulan#reset
resetting ...

復制代碼

6. 進入 recovery 命令行
本章所需硬件設備: 小米電視, 小米電視的遙控器, 章節 (3) 制作的調試線, PC (臺式機或筆記本)

6.1 按照章節 (5) 的方法進入 uboot 命令行

工廠數據

mulan#factorydata
factorydata - Access the factorydata from Xiaomi Partition
Usage:
factorydata argv:
dump
read keyname
write keyname value
erase keyname
mulan#factorydata dump
do_factorydata_dump : Got factory_power_mode[18] is [9]secondary
do_factorydata_dump : Got console_enable[14] is [1]0
do_factorydata_dump : Got pcba_mn[7] is [21]DZVCBCP3A12XXNXF00793
do_factorydata_dump : Got pcba_sn[7] is [21]DZVCBCP3A12XXNXF00793
do_factorydata_dump : Got assm_sn[7] is [17]48276106100061401
do_factorydata_dump : Got mac[3] is [17]78:53:33:10:dd:a5
do_factorydata_dump : Got did_key[7] is [39]00CB00073C3B|754663978|k5sBrXtwBJ6BLv5O
do_factorydata_dump : Got assm_mn[7] is [21]DZVCARF3B18TXNXX02321
do_factorydata_dump : Got bt_rc_mac[9] is [18]F4:22:7A:63:AE:6D;
do_factorydata_dump : Got log_level[9] is [1]0
do_factorydata_dump : Got mitv_screen_on[14] is [4]true
do_factorydata_dump : Got miot_beacon_pdu[15] is [38]0201060FFF8F030A10070F00ACE90FE18040E0
mulan#

復制代碼

6.2 啟用 console:

mulan#factorydata write console_enable 1

復制代碼

6.3 按照章節 (3) 的方法進入 recovery

Starting kernel ...
uboot time: 10638025 us
vmin:72 b2 6 0!
[VRTC]: xMboxGetRTC val=0x0
[cec_get_portinfo]: info=0x0
AOCPU unknown cmd=b5
#

復制代碼

好了, 我們進入 recovery 命令行了 ! 看一下基本信息

# type busybox
busybox is /sbin/busybox
# busybox id
uid=0(root) gid=0(root) context=u:r:shell:s0
# busybox getenforce
Permissive
# busybox uname -a
Linux localhost 4.9.113 #1 SMP PREEMPT Tue Apr 11 22:37:53 CST 2023 armv7l GNU/Linux
#

復制代碼

好, 我們是 root, 并且 SELinux 處于關閉狀態, 可以為所欲為了！

根目錄：

# busybox ls -al /
total 2080
__bionic_open_tzdata: couldn't find any tzdata when looking for localtime!
__bionic_open_tzdata: couldn't find any tzdata when looking for GMT!
__bionic_open_tzdata: couldn't find any tzdata when looking for posixrules!
drwxr-xr-x 27 root root 0 Jan 1 00:00 .
drwxr-xr-x 27 root root 0 Jan 1 00:00 ..
dr-xr-xr-x 4 root root 0 Jan 1 00:00 acct
lrwxrwxrwx 1 root root 11 Jan 1 1970 bin -> /system/bin
drwxr-xr-x 2 root root 0 Jan 1 1970 boot
lrwxrwxrwx 1 root root 50 Jan 1 1970 bugreports -> /data/user_de/0/com.android.shell/files/bugreports
drwxrwx--- 6 system cache 4096 Jan 1 00:03 cache
lrwxrwxrwx 1 root root 13 Jan 1 1970 charger -> /sbin/charger
drwxr-xr-x 4 root root 0 Jan 1 1970 config
lrwxrwxrwx 1 root root 17 Jan 1 1970 d -> /sys/kernel/debug
drwxr-xr-x 2 root root 0 Jan 1 1970 data
lrwxrwxrwx 1 root root 12 Jan 1 1970 default.prop -> prop.default
drwxr-xr-x 12 root root 5320 Jan 1 00:00 dev
drwxr-xr-x 2 root root 0 Jan 1 1970 etc
-rwxr-x--- 1 root root 1500384 Jan 1 1970 init
-rwxr-x--- 1 root root 2842 Jan 1 1970 init.rc
-rwxr-x--- 1 root root 14915 Jan 1 1970 init.recovery.amlogic.rc
drwxr-xr-x 2 root root 0 Jan 1 1970 metadata
drwxr-xr-x 3 root system 60 Jan 1 00:00 mnt
drwxr-xr-x 2 root root 0 Jan 1 1970 odm
drwxr-xr-x 2 root root 0 Jan 1 1970 oem
drwxr-xr-x 3 root root 0 Jan 1 1970 persist
-rw-r--r-- 1 root root 24584 Jan 1 1970 plat_file_contexts
-rw-r--r-- 1 root root 28976 Jan 1 1970 plat_property_contexts
dr-xr-xr-x 137 root root 0 Jan 1 1970 proc
drwxr-xr-x 2 root root 0 Jan 1 1970 product
-rw-r--r-- 1 root root 6676 Jan 1 1970 prop.default
drwxr-xr-x 3 root root 0 Jan 1 1970 res
drwx------ 2 root root 0 Apr 11 2023 root
drwxr-x--- 2 root root 0 Jan 1 1970 sbin
drwxr-xr-x 2 root root 0 Jan 1 1970 sdcard
-rw-r--r-- 1 root root 472377 Jan 1 1970 sepolicy
drwxr-xr-x 2 root root 0 Jan 1 00:00 sideload
drwxr-x--x 2 root root 0 Jan 1 1970 storage
dr-xr-xr-x 12 root root 0 Jan 1 00:00 sys
lrwxr-xr-x 1 root root 19 Jan 1 1970 system -> /system_root/system
drwxr-xr-x 2 root root 0 Jan 1 1970 system_root
drwxrwxr-x 2 root shell 80 Jan 1 00:00 tmp
drwx------ 3 root root 8192 Jan 1 1970 udisk
-rw-r--r-- 1 root root 5272 Jan 1 1970 ueventd.rc
drwxr-xr-x 5 root root 0 Jan 1 1970 vendor
-rw-r--r-- 1 root root 28202 Jan 1 1970 vendor_file_contexts
-rw-r--r-- 1 root root 4146 Jan 1 1970 vendor_property_contexts
#

復制代碼

7.在 uboot 下備份各個系統分區

本章所需硬件設備: 小米電視, 章節 (3) 制作的調試線, PC (臺式機或筆記本), U 盤 (1 個, 格式化為 FAT32 文件系統, 容量 8GB 以上)

8.在 recovery下備份各個系統分區

本章所需硬件設備: 小米電視, 小米電視的遙控器, 章節 (3) 制作的調試線, PC (臺式機或筆記本), U 盤 (1 個, 格式化為 FAT32 文件系統, 容量 8GB 以上).

8.1 插入 U 盤 (FAT32 格式), 然后進入 recovery

看一下分區

# busybox ls -al /dev/block
total 0
__bionic_open_tzdata: couldn't find any tzdata when looking for localtime!
__bionic_open_tzdata: couldn't find any tzdata when looking for GMT!
__bionic_open_tzdata: couldn't find any tzdata when looking for posixrules!
drwxr-xr-x 3 root root 820 Jan 1 00:00 .
drwxr-xr-x 12 root root 5320 Jan 1 00:00 ..
brw------- 1 root root 179, 11 Jan 1 00:00 boot
brw------- 1 root root 179, 1 Jan 1 00:00 bootloader
brw------- 1 root root 179, 3 Jan 1 00:00 cache
brw------- 1 root root 179, 9 Jan 1 00:00 cri_data
brw------- 1 root root 179, 22 Jan 1 00:00 data
brw------- 1 root root 179, 8 Jan 1 00:00 dtbo
brw------- 1 root root 179, 4 Jan 1 00:00 env
brw------- 1 root root 179, 17 Jan 1 00:00 factorydata
brw------- 1 root root 179, 5 Jan 1 00:00 logo
brw------- 1 root root 7, 0 Jan 1 00:00 loop0
brw------- 1 root root 7, 8 Jan 1 00:00 loop1
brw------- 1 root root 7, 16 Jan 1 00:00 loop2
brw------- 1 root root 7, 24 Jan 1 00:00 loop3
brw------- 1 root root 7, 32 Jan 1 00:00 loop4
brw------- 1 root root 7, 40 Jan 1 00:00 loop5
brw------- 1 root root 7, 48 Jan 1 00:00 loop6
brw------- 1 root root 7, 56 Jan 1 00:00 loop7
brw------- 1 root root 179, 13 Jan 1 00:00 metadata
brw------- 1 root root 179, 7 Jan 1 00:00 misc
brw------- 1 root root 179, 0 Jan 1 00:00 mmcblk0
brw------- 1 root root 179, 32 Jan 1 00:00 mmcblk0boot0
brw------- 1 root root 179, 64 Jan 1 00:00 mmcblk0boot1
brw------- 1 root root 179, 96 Jan 1 00:00 mmcblk0rpmb
brw------- 1 root root 31, 0 Jan 1 00:00 mtdblock0
brw------- 1 root root 179, 19 Jan 1 00:00 odm
brw------- 1 root root 179, 10 Jan 1 00:00 param
drwxr-xr-x 5 root root 100 Jan 1 00:00 platform
brw------- 1 root root 179, 21 Jan 1 00:00 product
brw------- 1 root root 179, 6 Jan 1 00:00 recovery
brw------- 1 root root 179, 2 Jan 1 00:00 reserved
brw------- 1 root root 179, 12 Jan 1 00:00 rsv
brw------- 1 root root 8, 0 Jan 1 00:00 sda
brw------- 1 root root 8, 1 Jan 1 00:00 sda1
brw------- 1 root root 179, 16 Jan 1 00:00 secure_recovery
brw------- 1 root root 179, 20 Jan 1 00:00 system
brw------- 1 root root 179, 15 Jan 1 00:00 tee
brw------- 1 root root 179, 14 Jan 1 00:00 vbmeta
brw------- 1 root root 179, 18 Jan 1 00:00 vendor
brw------- 1 root root 254, 0 Jan 1 00:00 zram0

復制代碼

掛載狀態

# busybox mount
rootfs on / type rootfs (rw,seclabel)
tmpfs on /dev type tmpfs (rw,seclabel,nosuid,relatime,mode=755)
devpts on /dev/pts type devpts (rw,seclabel,relatime,mode=600,ptmxmode=000)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,seclabel,relatime)
selinuxfs on /sys/fs/selinux type selinuxfs (rw,relatime)
tmpfs on /mnt type tmpfs (rw,seclabel,nosuid,nodev,noexec,relatime,mode=755,gid=1000)
none on /acct type cgroup (rw,relatime,cpuacct)
tmpfs on /tmp type tmpfs (rw,seclabel,relatime)
none on /config type configfs (rw,relatime)
adb on /dev/usb-ffs/adb type functionfs (rw,relatime)
/dev/block/sda1 on /udisk type vfat (rw,nodev,noatime,nodiratime,fmask=0077,dmask=0077,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/block/cache on /cache type ext4 (rw,seclabel,nodev,noatime,nodiratime,discard,data=ordered)
# busybox ls -al /udisk
total 16
__bionic_open_tzdata: couldn't find any tzdata when looking for localtime!
__bionic_open_tzdata: couldn't find any tzdata when looking for GMT!
__bionic_open_tzdata: couldn't find any tzdata when looking for posixrules!
drwx------ 3 root root 8192 Jan 1 1970 .
drwxr-xr-x 27 root root 0 Jan 1 00:00 ..
drwx------ 2 root root 8192 Dec 26 2023 202312
#

復制代碼

recovery 已經自動將 U盤掛載到了 /udisk 目錄

8.2 備份除了 data (用戶數據) 外的所有分區

# busybox dd if=/dev/block/boot of=/udisk/boot.img
32768+0 records in
32768+0 records out
16777216 bytes (16.0MB) copied, 0.417935 seconds, 38.3MB/s
#

復制代碼

重復使用 dd 命令, 具體需要備份的分區可以參考以下列表:

# busybox ls -al /udisk
total 3072016
__bionic_open_tzdata: couldn't find any tzdata when looking for localtime!
__bionic_open_tzdata: couldn't find any tzdata when looking for GMT!
__bionic_open_tzdata: couldn't find any tzdata when looking for posixrules!
drwx------ 3 root root 8192 Jan 1 00:21 .
drwxr-xr-x 27 root root 0 Jan 1 00:00 ..
drwx------ 2 root root 8192 Dec 26 2023 202312
-rwx------ 1 root root 16777216 Jan 1 00:05 boot.img
-rwx------ 1 root root 4194304 Jan 1 00:06 bootloader.img
-rwx------ 1 root root 536870912 Jan 1 00:13 cache.img
-rwx------ 1 root root 8388608 Jan 1 00:16 cri_data.img
-rwx------ 1 root root 8388608 Jan 1 00:17 dtbo.img
-rwx------ 1 root root 8388608 Jan 1 00:17 env.img
-rwx------ 1 root root 10485760 Jan 1 00:18 factorydata.img
-rwx------ 1 root root 8388608 Jan 1 00:20 logo.img
-rwx------ 1 root root 16777216 Jan 1 00:18 metadata.img
-rwx------ 1 root root 8388608 Jan 1 00:20 misc.img
-rwx------ 1 root root 4194304 Jan 1 00:12 mmcblk0boot0.img
-rwx------ 1 root root 4194304 Jan 1 00:12 mmcblk0boot1.img
-rwx------ 1 root root 134217728 Jan 1 00:16 odm.img
-rwx------ 1 root root 16777216 Jan 1 00:17 param.img
-rwx------ 1 root root 33554432 Jan 1 00:19 product.img
-rwx------ 1 root root 25165824 Jan 1 00:21 recovery.img
-rwx------ 1 root root 67108864 Jan 1 00:21 reserved.img
-rwx------ 1 root root 16777216 Jan 1 00:12 rsv.img
-rwx------ 1 root root 33554432 Jan 1 00:16 secure_recovery.img
-rwx------ 1 root root 1610612736 Jan 1 00:24 system.img
-rwx------ 1 root root 33554432 Jan 1 00:17 tee.img
-rwx------ 1 root root 2097152 Jan 1 00:18 vbmeta.img
-rwx------ 1 root root 536870912 Jan 1 00:20 vendor.img
#

復制代碼

8.3 重啟設備, 拔出 U 盤

然后把上述獲得的分區鏡像文件, 打包壓縮一下, 找個安全的地方備份起來 (建議上傳網盤), 以后對于救磚有重要用途

上述整個操作過程中獲得的各種信息 (UART 輸出), 也建議保存?zhèn)溆?br />
以上就是我對”小米電視root需要做哪些準備工作？2024小米電視刷機詳細教程”的內容分享，如果還有其他問題可以在評論區留言。

相關閱讀：
海信電視如何精簡系統？海信電視刷機簡化系統操作教程

1235qwerfgk · 發表于 2024-7-8 13:13

來看看這個

NRD90M · 發表于 2024-8-5 09:22

小米電視大師77寸oled，按住確認和返回命令行提示no recovery mod，adb重啟到recovery無法輸入，沒有#

yhyzhj · 發表于 2024-8-6 18:13

要膽大心細

隨便就看見了 · 發表于 2024-8-12 10:57

好貼，雖然我看不懂

yuan185 · 發表于 2024-9-20 12:06

那請問怎么 root 呢用busybox DD命令提取的BOOT.IMG去修補，修補完了之后刷進去之后不進系統，只能進REC。
在鏈接教程2中我失敗在安裝magisk.zip這一步，提示error127,提示安裝失敗不知道怎么搞了

siphot · 發表于 2024-9-26 23:18

yuan185 發表于 2024-9-20 12:06
那請問怎么 root 呢用busybox DD命令提取的BOOT.IMG去修補，修補完了之后刷進去之后不進系統，只能進RE ...

估計要TTL輸入命令關閉下AVB才行

chtwflm · 發表于 2024-10-19 21:20

樓主能分享一份2.8.2129 (穩定版)..固件嗎？

› 智能電視 / 安卓TV區 › 小米電視

小米電視root需要做哪些準備工作？2024小米電視刷機詳細 ...

小米電視root需要做哪些準備工作？2024小米電視刷機詳細教程

相關帖子